OGUZLAR BILGISAYAR LTD.STI.

### AnkiSOFT Software – isuCAD
### WATER SUPPLY NETWORK DESIGN SOFTWARE
### For Drawing / Modelling / Planning / Design / Analyze / Simulation



Since 1985,**AnkiSOFT Software** developes software to design **Infrastructure Projects**. **isuCAD** has been developed for **Water Supply Network Design**. It is for Drawing / Modelling / Planning / Design / Analyze / Simulation of the **Water Supply Network**.

The software works under **AutoCAD** or **ZWCAD**.


### DRAWING the NETWORK

Design/analyze method can be **DEAD-END** or **HARDY-CROSS**. For the **HARDY-CROSS** method, the software works with **EPANET 2.0**.

It is possible to arrange the drawing style by using STYLE MANAGER, so you can use different drawing style in different projects.

OPEN LAYER command can open all the necessary layers that the software needs.
You can define/draw/edit/delete/move Demand Node (DN), can change some/all properties of DNs. The software will write; DNno and the ground elevation for each DN on the drawing.
You can find any DN by searching the DNno, can change the location of DNno, can renumber some/all DNnos from a specified number.

You can define/draw/edit/delete pipes, can change the direction of pipes, can change some/all properties of pipes. The software will write; diameter, length and length-coefficient for each pipe on the drawing.

You can define/draw/delete embedded reservoir, elevated reservoir, pump-station, hydrophore.
You can define/draw/delete point-discharge to any pipes.

Our software produces EPANET.INP file. You can use it in EPANET or WaterCAD directly. And also, if you have any EPANET.INP file exported from EPANET or WaterCAD, you can transfer all the network and information to our software directly too.


### ERROR CHECKING

You can check weather there is any mistake in the network model. You can find and you can correct them.

Such as; same DNnos, 1st-phase - 2nd-phase - existing pipe connections, pipe connections from/to DNs.


### DESIGN CRITERION

**You can define:**
* Elevation of coming pipe to the reservoir
* Bottom elevation of the reservoir
* Allowable minimum-operation-pressure for the network
* Allowable maximum-static-pressure for the network
* Peak factor for the network
* Fire discharge values and minimum pipe diameters for main, primary and secondary pipes
* For each Type-DIAMETER; type-name, material (concrete, reinforced concrete, PVC, ACB, Steel, HDPE, Ribloc, ...), inner diameter, allowable maximum velocity, design formula (William Hazen, Ludin, ...), "C" values (roughness coefficient) for the formula.


### HYDRAULIC DESIGN

During design works; all the information on the drawing will be send to calculation, the calculation software will do hydraulic calculations, then all the calculated information will be send back to the drawing to show the final situation.

You can repeat this process, until you reached to the situation that you want.


### STEADY STAYE ANALYSIS

Steady State Analysis depends on maximum hourly pik demand.
During analiysis, the software recommends diameter for the pipes. The software also informs you about the pipes having higher velocity and pressures than design-criterion.


### WATER SUPPLY NETWORK SIMULATION (Extended Period Simulation, EPS)

Water Supply Network Simulation starts when the water tank is full. A pattern having 72-hours can be used.

During simulation, the software recommends diameter for the pipes. The software also informs you about the pipes having higher velocity and pressures than design-criterion.


### DESIGN CALCULATION TABLES

Hydraulic calculations are in the form of tables and recorded in a text file.
* DNno at the start
* DNno at the end
* Phase number
* Pipe length
* Length-coefficient
* Relative pipe length
* Qpipe, Qstart, Qend, Qaverage, Qtotal, Qfire and Qdesign
* Selected diameter
* Head loss per meter
* Velocity
* Total headloss
* Piezometric elevation at end DN
* Ground elevation at end DN
* Pressure head at end DN
* Remark for each pipe
Next table contains; pipe lengths according to pipe diameter and phase of pipe.
The last table contains; excavation amounts according to excavation depth and phase of pipe.


### CALCULATION PLAN

You can prepare calculation plan from network model. In this plan you can see, pipe directions, pipe lengths, pipe diameter and pipe length-coefficients.
You can prepare the plan by the use of only one command in a very short time.


### CONSTRUCTION PLAN

You can arrange primary/secondary pipe separation valves automatically. You can define/delete valve at start/end of pipes, can add/delete water-drain-valves at desired DNs, can define/delete fire-hydrants on pipes. You can prepare the plan by the use of only one command in a very short time.


### GENERAL LAYOUT PLAN (1/5000)
The software will show main and primary pipes and DNnos automatically. Also, you can decide for other pipes/DNs to show on general layout plan. Then, you can prepare general layout plan in a very short time.


### NODE DETAIL DRAWING

All of the fittings are recorded in a text file for you. You can add/delete your fittings to that file, can change the appearance order, so you can show your own style.

Typical DN details and the fittings are recorded in a text file for you too. You can add/delete to typical DN details, can change appearance order, so you can show your own style.

Shortly, you can teach the fittings and the usage of them to the software. After then, the software will prepare DN detail drawing in this way.

**In the drawings:**
* There will be an empty place on the right side of the drawing for legend.
* There will be a border line for the drawing, also another border line for cutting.
* The output is in DXF file format.


### FITTINGS LIST DRAWING

Everything will be ready after DN detail drawing works. It is easy for you to prepare fittings list drawing. The only thing that you have to do is; to select the phase and to use our command for each of your selection.

**In the drawings:**
* There will be an empty place on the right side of the drawing for legend.
* There will be a border line for the drawing, also another border line for cutting.
* The output is in DXF file format.


### INFORMATION TRANSFER

You can transfer easily all the network information to another drawing/computer, or vice versa.


### GENERAL

* There is no limit to the number of DNs and pipes.
* There is no limit to the number of dead-end-nodes.
* There is no limit to the number of pipe diameters and pipe materials.
* It is possible to have more than one network on the same drawing. There is no limit to the number of networks.
* It is possible to define different discharge zones, different length-coefficient zones.
* It is possible to define 1st-phase, 2nd-phase and existing pipe.
* During design works; it is possible to change pipe diameter.
* During design works; the software can show the logical mistakes of the network to the user to correct them.
* It is possible to see the DNs having less pressure than allowable-minimum-operation pressure and having higher pressure than allowable-maximum-static pressure.
* It is possible to see pressure difference at dead-end-nodes.
* At the end of the hydraulic calculation, software will supply excavation amounts and pipe lengths.
* The software can prepare classified pipe list according to phase, diameter and material.
* The software can renumber DN numbers automatically.
* All calculations are in a text file, in the form of tables. You can open, you can copy, you can print directly at any time.
* You can print the above text files by using an A4-printer with the help of our software commands too.
* You can use our software commands with AutoCAD or ZWCAD commands too.


### UPGRADE HISTORY

**JANUARY.2023**

AutoCAD 2021 x64, ZWCAD 2024 x64
Windows11 x64, Windows10 x64
NET Framework 4
Sentinel HASP HL Pro Driverless, Sentinel-LDK\_SDK\_7.6 x64
EPANET 2.0 x32

**JANUARY.2021**

AutoCAD 2021 x64, ZWCAD 2022 x64
Windows8.1 x64, Windows8.0 x64, Windows7 x64
NET Framework 4
Sentinel HASP HL Pro Driverless, Sentinel-LDK\_SDK\_7.6 x64
EPANET 2.0 x32

**JANUARY.2018**

JANUARY.201864, ZWCAD 2018 x64
Windows7 x64, Windows8.0 x64, Windows8.1 x64, Windows10 x64
Sentinel HASP HL Pro Driverless, Sentinel-LDK\_SDK\_7.6 x64
EPANET 2.0 x32

**MAY.2017**

AutoCAD 2017 x64, ZWCAD+ 2015 x64
Windows7 x64, Windows8.0 x64, Windows8.1 x64, Windows10 x64
Sentinel HASP HL MaxMicro Driverless, Sentinel-LDK\_SDK\_7.1 x64
EPANET 2.0 x32

**JANUARY.2015**

AutoCAD 2015 x64, ZWCAD+ 2015 x64
Windows7 x64, Windows8.0 x64, Windows8.1 x64
Sentinel HASP HL MaxMicro Driverless, Sentinel-LDK\_SDK\_7.1 x64
EPANET 2.0 x32

**JANUARY.2013**

AutoCAD 2013 x64
Windows7 x64
Sentinel HASP HL Max, Sentinel-HASP\_SDK\_5.12 x64

**JUNE.2012**

AutoCAD 2012 x64
Windows7 x64, Windows8.0 x64, Windows8.1 x64
Sentinel HASP HL Max, Sentinel-HASP\_SDK\_5.12 x64

**JANUARY.2012**

AutoCAD 2012 x32, ZWCAD 2012
Windows7 x32
Sentinel HASP HL Max, Sentinel-HASP\_SDK\_5.12 x64

 **JANUARY.2010**

AutoCAD 2010 x32
WindowsXP x32
Aladdin HASP HL Max, Ver1.1 x32

**JANUARY.2009**

AutoCAD 2008 x32
WindowsXP x32
Aladdin HASP HL Max, Ver1.1 x32

**JANUARY.2003**

AutoCAD 2004 x32
WindowsXP x32

**JANUARY.1986**

MSDOS

WATER SUPPLY NETWORK DESIGN SOFTWARE
For Drawing / Modelling / Planning / Design / Analyze / Simulation

isuCAD

isuCAD - rent

### AnkiSOFT Software – pissuCAD
### WASTEWATER NETWORK DESIGN SOFTWARE
### For Drawing / Modelling / Planning / Design / Analyze / Simulation



Since 1985, **AnkiSOFT Software** developes software to design **Infrastructure Projects**. **pissuCAD** has been developed for **Wastewater (sewerage) Network Design**. It is for Drawing / Modelling / Planning / Design / Analyze / Simulation of the wastewater network.

The software works under **AutoCAD** or **ZWCAD**.


### DRAWING the NETWORK

OPEN LAYER command can open all the necessary layers that the software needs.

You can define/draw/edit/delete/move manholes (MH), can change some/all properties of MHs. The software will write; MHno and the ground elevation for each MH on the drawing.

You can find any MH by searching the MHno, can change the location of MHno, can renumber some/all MHnos from a specified number.

You can define/draw/edit/delete pipes, can change the direction of pipes, can change some/all properties of pipes. The software will write; start-invert-elevation, diameter, length, slope and end-invert-elevation for each pipe on the drawing.

You can show depths, discharge and fullness ratio of all pipes on the drawing.

You can define/draw/delete pump-station/fosseptic.

You can define/draw/delete point-discharge to any pipes.


### ERROR CHECKING

Such as; same MHnos, 1st-phase - 2nd-phase - existing pipe connections, pipe connections from/to MHs, pipes going from lower elevation to higher elevation.


### DESIGN CRITERION

• Allowable minimum elevation difference for pipes
• Allowable minimum water drop head depth
• Pipes can have circular cross-section or rectangular cross-section (box).
• For each Type-DIAMETER; type-name, material (concrete, reinforced concrete, PVC, ACB, Steel, HDPE, Ribloc, ...), inner diameter, allowable minimum slope, allowable maximum slope, allowable maximum fullness ratio, design formula (Kutter, Manning, ...), "a" or "n" values (roughness ratio) for the formula.


### HYDRAULIC DESIGN

You can repeat this process, until you reached to the situation that you want.

WASTEWATER NETWORK SIMULATION (Extended Period Simulation - EPS)


### WASTEWATER NETWORK SIMULATION (Extended Period Simulation - EPS)

The pipes having higher velocity/fullness ratio will be shown in different notation. So, you can check the network in minimum time.

For More Information about Wastewater Network Simulation Please Click


### DESIGN CALCULATION TABLES

• MHno at the start
• MHno at the end
• Phase number
• Discharge zone number
• Pipe length
• Unit discharge
• MHno bringing water
• Amount of incoming water
• Qtotal
• Start ground elevation
• End ground elevation
• Inner-top elevation of pipe at the start
• Inner-top elevation of pipe at the end
• Inner-bottom elevation of pipe at the start
• Inner-bottom elevation of pipe at the end
• Inner-top depth of pipe at the start
• Inner-top depth of pipe at the end
• Slope
• Selected diameter
• Fullness ratio
• Capacity at %50 fullness
• Velocity
• Water depth

Next table contains; pipe lengths according to pipe diameter and phase of pipe.

The last table contains; excavation amounts according to excavation depth and phase of pipe.


### GENERAL LAYOUT PLAN (1/5000)

The software will show collector pipes and MHs automatically. Also, you can decide for other pipes/MHs to show on general layout plan.

Then, you can prepare general layout plan in a very short time.


### PROFILE DRAWING

Now, everything is ready after design works. So, it is easy for you to prepare the profile.

The only thing that you have to do is; to decide the phase (1st-phase/2nd-phase/existing).

After writing vertical and horizontal scale, you can prepare the profile by the use of only one command.

By using the profile software;

• You can draw profile without any length limit at one time.
• The drawing-height is set to 297 mm.
• To be able to draw the profile within the drawing-height, reference elevations will be arranged automatically.
• The information on the profile is;

• Pipe depth
• Reference elevation
• MHnos for connected pipes
• MHno
• Ground elevation
• Inner-bottom elevation of pipe
• Pipe length
• Slope (1/a)
• Pipe diameter/box sizes

• There will be an empty place on the right side of the drawing for legend.
• There will be a border line for the drawing, also another border line for cutting.
• The output is in DXF file format.


### DETAILED EXCAVATION

It is easy for you to get the amounts, because, all the information are ready after the design works.

You can define some general information; excavation slope, the road pavement thicknesses (asphalt, concrete, stone, stabilized, natural).

For typical MHs; type-name, inner diameter, outer diameter, width of bottom-concrete, bottom width of excavations (sloped excavation, wooden-bracing, steel-bracing and 5 different sheet-pile-wall), the backfill thicknesses (sub-base layer, sand-base layer and bottom-concrete).

For typical pipes; pipe-class in the network (small-diameter, medium-diameter or collector), pipe-name, backfill-type-number, inner diameter, outer diameter, bottom width of excavations (sloped excavation, wooden-bracing, steel-bracing and 5 different sheet-pile-wall), the backfill thicknesses (sub-base layer, sand-base layer and top backfill layer).


### EXCAVATION TABLES

The output table for MHs contains;

• MHno
• Phase
• The greatest diameter of outgoing pipe.
• Inner diameter of MH
• Outer diameter of MH
• Width of bottom-concrete
• Bottom width of excavation
• Inner-bottom depth of MH
• Backfill thicknesses (sub-base layer, sand-base layer and bottom-concrete)
• Excavation depth
• Excavation amounts depending on depths
• Total excavation amount
• Volume of the concrete MH
• Road pavement information (type, thickness, area and volume)
• Backfill thickness (sub-base layer, sand-base layer and bottom-concrete)
• Backfill type and volume
• Excavation and type of bracing
• The depth of bracing
• The area of bracing

The output table for pipes contains;

• MHno at the start
• MHno at the end
• Phase
• Pipe information (diameter, outer diameter, bottom width of excavation and length)
• Bottom width of excavation for MH
• Excavation length
• Inner-bottom depths at start and at end
• Backfill thicknesses (sub-base layer, sand-base layer and top backfill layer)
• Excavation depths at start and at end
• Excavation amounts depending on depths
• Total excavation amount
• Pipe volume
• Road pavement information (type, thickness, area and volume)
• Backfill amount (sub-base layer, sand-base layer and top backfill layer)
• Backfill type and volume
• Excavation and type of bracing
• The depth of bracing
• The area of bracing

During the excavation calculations;

If the excavation width at top is less than or equal to 1.00 m., the excavation is called as narrow-deep-excavation.
If it is greater than 1.00 m., then the excavation is called as wide-deep-excavation.


### SUMMARY TABLES of DETAILED EXCAVATION

For MHs, at summary-total tables; excavation amounts according to depths, backfill amounts according to backfill-type, bracing amounts according support-type, road pavement amounts according to pavement-type, in the base of small-diameter, medium-diameter or collector.

For pipes; excavation and bracing summaries are in the form of tables according to phase.

For pipes, at summary-total tables; excavation amounts according to depths (for the both of narrow-deep-excavation and wide-deep-excavation), backfill amounts according to backfill-type, bracing amounts according bracing-type, road pavement amounts according to pavement-type, in the base of small-diameter, medium-diameter or collector.

For MHs+pipes; excavation, backfill and bracing summaries are in the form of tables according to phase.

For pipes; pipe lengths at project and pipe lengths at construction are in the form of tables according to pipe diameter and phase.


### INFORMATION TRANSFER

You can transfer easily all the network information to another drawing/computer, or vice versa.
GENERAL


### GENERAL

• There is no limit to the number of pipe diameters and pipe materials.
• It is possible to have more than one network on the same drawing. There is no limit to the number of networks.
• It is possible to define different discharge zones.
• It is possible to define 1st-phase, 2nd-phase and existing pipe.
• During design works; it is possible to change pipe diameter, start/end elevation of pipes.
• During design works; the software can show the logical mistakes of the network to the user to correct them.
• During design works; if a pipe exceeds the hydraulic/design criterion, the software informs the user.
• At the end of the hydraulic calculation, software will supply excavation amounts and pipe lengths.
• The software can renumber MH numbers automatically.
• The software can transfer the MH information to topographic work, and can get back those changed information from topographic works (by using a text file).
• The software can prepare the deepness-map for geological work.
• All calculations are in a text file, in the form of tables. You can open, you can copy, you can print directly at any time.
• You can print the above text files by using an A4-printer with the help of our software commands too.
• You can use our software commands with AutoCAD or ZWCAD commands too.


### UPGRADE HISTORY

**JANUARY 2023**

AutoCAD 2021 x64, ZWCAD 2024 x64
Windows11 x64, Windows10 x64
.NET Framework 4.8
Sentinel HL Pro Driverless, Sentinel-LDK_SDK_9.0 x64

**JANUARY.2021**

AutoCAD 2021 x64, ZWCAD 2022 x64
Windows8.1 x64, Windows8.0 x64, Windows7 x64
.NET Framework 4
Sentinel HL Pro Driverless, Sentinel-LDK_SDK_7.6 x64

**MAY.2017**

AutoCAD 2017 x64, ZWCAD+ 2015 x64
Windows7 x64, Windows8.0 x64, Windows8.1 x64, Windows10 x64
Sentinel HASP HL MaxMicro Driverless, Sentinel-LDK_SDK_7.1 x64

**JANUARY.2015**

AutoCAD 2015 x64, ZWCAD+ 2015 x64
Windows7 x64, Windows8.0 x64, Windows8.1 x64
Sentinel HASP HL MaxMicro Driverless, Sentinel-LDK_SDK_7.1 x64

**JANUARY.2013**

AutoCAD 2013 x64
Windows7 x64
Sentinel HASP HL Max, Sentinel-HASP_SDK_5.12 x64

**JUNE.2012**

AutoCAD 2012 x64
Windows7 x64, Windows8.0 x64, Windows8.1 x64
Sentinel HASP HL Max, Sentinel-HASP_SDK_5.12 x64

**JANUARY.2012**

AutoCAD 2012 x32, ZWCAD 2012
Windows7 x32
Sentinel HASP HL Max, Sentinel-HASP_SDK_5.12 x64

**JANUARY.2010**

AutoCAD 2010 x32
WindowsXP x32
Aladdin HASP HL Max, Ver1.1 x32

**JANUARY.2009**

AutoCAD 2008 x32
WindowsXP x32
Aladdin HASP HL Max, Ver1.1 x32

**JANUARY.2003**

AutoCAD 2004 x32
WindowsXP x32

**JANUARY.1999**

AutoCAD 2000
Windows98

**JANUARY.1997**

ACAD 14
Windows98

**JANUARY.1985**

MSDOS

WASTEWATER NETWORK DESIGN SOFTWARE
For Drawing / Modelling / Planning / Design / Analyze / Simulation

pissuCAD

pissuCAD - rent

### AnkiSOFT Software – yasuCAD
### STORMWATER NETWORK DESIGN SOFTWARE
### For Drawing / Modelling / Planning / Design / Analyze



Since 1985 **AnkiSOFT Software** developes software to design **Infrastructure Projects**. **yasuCAD** has been developed for **Stormwater Network Design**. It is for Drawing / Modelling / Planning / Design / Analyze of the stormwater network.

The software works under **AutoCAD** or **ZWCAD**.


### DRAWING the NETWORK

It is possible to arrange the drawing style by using STYLE MANAGER, so you can use different drawing style in different projects.

OPEN LAYER command can open all the necessary layers that the software needs.

You can define/draw/edit/delete/move manholes (MH), can change some/all properties of MHs. The software will write; MHno and the ground elevation for each MH on the drawing.

You can find any MH by searching the MHno, can change the location of MHno, can renumber some/all MHnos from a specified number.

You can define/draw/edit/delete pipes, can change the direction of pipes, can change some/all properties of pipes. The software will write; start-invert-elevation, diameter, length, slope and end-invert-elevation for each pipe on the drawing.

You can define/draw/edit/delete/move catchment area, you can change connected MH. You can define/delete concentrated catchment area. You can define/delete grid.

You can show depths, discharge and fullness ratio of all pipes on the drawing.


### ERROR CHECKING

You can check weather there is any mistake in the network model. You can find and you can correct them.

Such as; same MHnos, 1st-phase - 2nd-phase - existing pipe connections, pipe connections from/to MHs, pipes going from lower elevation to higher elevation.


### DESIGN CRITERION

* Allowable minimum elevation difference for pipes.
* Allowable minimum water drop head depth
* Pipes can have circular cross-section or rectangular cross-section (box).
* For each Type-DIAMETER; type-name, material (concrete, reinforced concrete, PVC, ACB, Steel, HDPE, Ribloc, ...), inner diameter, allowable minimum slope, allowable maximum slope, allowable maximum fullness ratio, design formula (Kutter, Manning, ...), "a" or "n" values (roughness ratio) for the formula.


### HYDRAULIC DESIGN

You can repeat this process, until you reached to the situation that you want.


### DESIGN CALCULATION TABLES

• MHno at the start
• MHno at the end
• Phase number
• Discharge zone number
• Pipe length
• Drainage area
• Runoff coefficient
• Relative area
• Total relative area
• Concentration time
• Rainfall intensity
• Qdesign
• Slope
• Selected diameter
• Velocity
• Flow time
• Water depth
• Fullness ratio
• Capacity at %100 fullness
• Ground elevation at the start
• Ground elevation at the end
• Inner-top elevation of pipe at the start
• Inner-top elevation of pipe at the end
• Inner-bottom elevation of pipe at the start
• Inner-bottom elevation of pipe at the end
• Inner-bottom depth of pipe at the start
• Inner-bottom depth of pipe at the end

Next table contains; pipe lengths according to pipe diameter and phase of pipe.

The last table contains; excavation amounts according to excavation depth and phase of pipe.


### GENERAL LAYOUT PLAN (1/5000)

Then, you can prepare general layout plan in a very short time.


### PROFILE DRAWING

After writing vertical and horizontal scale, you can prepare the profile by the use of only one command.

By the use of profile software;

• You can draw profile without any length limit at one time.
• The drawing-height is set to 297 mm.
• To be able to draw the profile within the drawing-height, reference elevations will be arranged automatically.
• The information on the profile are;

• Pipe depth
• Reference elevation
• MHnos for connected pipes
• MHno
• Ground elevation
• Inner-bottom elevation of pipe
• Pipe length
• Slope (1/a)
• Pipe diameter/box sizes

• There will be an empty place on the right side of the drawing for legend.
• There will be a border line for the drawing, also another border line for cutting.
• The output is in DXF file format.


### INFORMATION TRANSFER

• There is no limit to the number of MHs and pipes.
• There is no limit to the number of pipe diameters and pipe materials.


### GENERAL

• During design works; it is possible to change pipe diameter, start/end elevation of pipes.
• During design works; the software can show the logical mistakes of the network to the user to correct them.
• During design works; if a pipe exceeds the hydraulic/design criterion, the software informs the user.
• At the end of the hydraulic calculation, software will supply excavation amounts and pipe lengths.
• The software can renumber MH numbers automatically.
• The software can transfer the MH information to topographic work, and can get back those changed information from topographic works (by using a text file).
• The software can prepare the deepness-map for geological work.
• All calculations are in a text file, in the form of tables. You can open, you can copy, you can print directly at any time.
• You can print the above text files by using an A4-printer with the help of our software commands too.
• You can use our software commands with AutoCAD or ZWCAD commands too.


### UPGRADE HISTORY

**JANUARY 2023**

AutoCAD 2021 x64, ZWCAD 2024 x64
Windows11 x64, Windows10 x64
.NET Framework 4.8
Sentinel HL Pro Driverless, Sentinel-LDK_SDK_9.0 x64

**JANUARY.2021**

AutoCAD 2021 x64, ZWCAD 2022 x64
Windows8.1 x64, Windows8.0 x64, Windows7 x64
.NET Framework 4
Sentinel HL Pro Driverless, Sentinel-LDK_SDK_7.6 x64

**JANUARY.2018**

AutoCAD 2018 x64, ZWCAD 2018 x64
Windows7 x64, Windows8.0 x64, Windows8.1 x64, Windows10 x64
Sentinel HASP HL Pro Driverless, Sentinel-LDK_SDK_7.6 x64

**MAY.2017**

AutoCAD 2017 x64, ZWCAD+ 2015 x64
Windows7 x64, Windows8.0 x64, Windows8.1 x64, Windows10 x64
Sentinel HASP HL MaxMicro Driverless, Sentinel-LDK_SDK_7.1 x64

**JANUARY.2015**

AutoCAD 2015 x64, ZWCAD+ 2015 x64
Windows7 x64, Windows8.0 x64, Windows8.1 x64
Sentinel HASP HL MaxMicro Driverless, Sentinel-LDK_SDK_7.1 x64

**JANUARY.2013**

AutoCAD 2013 x64
Windows7 x64
Sentinel HASP HL Max, Sentinel-HASP_SDK_5.12 x64

**JUNE.2012**

AutoCAD 2012 x64
Windows7 x64, Windows8.0 x64, Windows8.1 x64
Sentinel HASP HL Max, Sentinel-HASP_SDK_5.12 x64

**JANUARY.2012**

AutoCAD 2012 x32, ZWCAD 2012
Windows7 x32
Sentinel HASP HL Max, Sentinel-HASP_SDK_5.12 x64

**JANUARY.2010**

AutoCAD 2010 x32
WindowsXP x32
Aladdin HASP HL Max, Ver1.1 x32

**JANUARY.2009**

AutoCAD 2008 x32
WindowsXP x32
Aladdin HASP HL Max, Ver1.1 x32

**JANUARY.2003**

AutoCAD 2004 x32
WindowsXP x32

**JANUARY.1987**

MSDOS

STORMWATER NETWORK DESIGN
For Drawing / Modelling / Planning / Design / Analyze

yasuCAD

yasuCAD - rent

### AnkiSOFT Software – isaleCAD
### WATER TRANSMISSION LINE DESIGN SOFTWARE
### For Drawing / Modelling / Planning / Design / Analyze



Since 1985, **AnkiSOFT Software** developes software to design **Infrastructure Projects**. **isaleCAD** has been developed for **Water Transmission Line Design**. It is for Drawing / Modelling / Planning / Design / Analyze of the water transmission line.

The software works under **AutoCAD** or **ZWCAD**.


### DRAWING the NETWORK

It is possible to arrange the drawing style by using STYLE MANAGER, so you can use different drawing style in different projects.

OPEN LAYER command can open all the necessary layers that the software needs.

You can define/draw/edit/delete/move Station nodes/Keeper nodes (SK), can change some/all properties of SKs. The software will write; SKno and the ground elevation for each SK on the drawing.

You can find any SK by searching the SKno, can change the location of SKno, can renumber some/all SKnos from a specified number.

You can define/draw/edit/delete pipes, can change the direction of pipes, can change some/all properties of pipes.

You can define/draw/delete air-releasing-valve/water-drain-valve to any SK. You can renumber them.


### ERROR CHECKING

You can check weather there is any mistake in the network model. You can find and you can correct them.

Such as; same SKnos, pipe connections from/to SKs.


### DESIGN CRITERION

You can define;

• Water supply point can be; pump-station, embedded-reservoir, elevated-reservoir or pressure-decreasing-valve
• Water destination point can be; embedded-reservoir, elevated-reservoir, pressure-decreasing-valve, network enterance node or water-drain-valve
• Profile drawing height
• You can decide air-releasing-valve/water-drain-valve, or software will decide them itself, or software and you can decide together
• The software will decide vertical curve fittings automatically
• If the pipe slope is greater than or equal to 30%, software will add backfill-supporting-wall automatically
• Curve angles can be in degree/grad
• Pressure calculations can be according to pipe bottom elevation or pipe center elevation
• The output is in DXF file format
• For each Type-DIAMETER; type-name, material (concrete, reinforced concrete, PVC, ACB, Steel, Cast iron, Ductile iron, HDPE, CTP, ...), allowable pressure, wall thickness, inner diameter, pipe discharge, design formula (William-Hazen, Ludin, ...), "C" values for the formula, outer diameter and basement layer thickness.


### HYDRAULIC DESIGN

During design works; all the information on the drawing will be send to calculation, the calculation software will do hydraulic calculations, then all the calculated information will be send back to the drawing to show the final situation.

You can repeat this process, until you reached to the situation that you want.


### DESIGN CALCULATION TABLES

Hydraulic calculations are in the form of tables and recorded in a text file. In the first table;

• SKno
• Distance from the beginning
• Ground elevation
• Pipe elevation
• Total JL
• Total local head loss (LK)
• Total JL+LK
• Piesometric elevation
• Pressure during operation
• Maximum pressure
• Minimum pressure.

In the second table;

• SKno
• Air-releasing-valve/water-drain-valve name
• Angle of horizontal curve
• Angle of vertical curve
• Angle of 3D curve.


### PROFILE

The information on the profile is;

• Excavation depth
• SKno
• Ground elevation
• Pipe center/bottom elevation
• Distance between SKs
• Distance from the beginning
• Pipe diameter and material type
• Slope
• Direction on the plan. All of them will be prepared automatically.


### SCHEMATICAL PROFILE

The information on the profile is;

• Maximum pressure line
• Piesometric line
• Static line
• Minimum pressure line
• SKno
• Pipe center/bottom elevation
• Distance between SKs
• Distance from the beginning
• Pressure during operation
• Maximum and minimum pressure during water hammer
• Static pressure
• Pipe diameter and material type. All of them will be prepared automatically.


### INFORMATION TRANSFER

You can transfer easily all the network information to another drawing/computer, or vice versa.


### GENERAL

• There is no limit to the number of SKs and pipes.
• There is no limit to the number of pipe diameters and pipe materials.
• It is possible to have more than one transmission line on the same drawing. There is no limit to the number of transmission line.
• During design works; the software can show the logical mistakes of the transmission line to the user to correct them.
• On the schematic profile; you can see the SKs having pressure less than minimum-operational-pressure and having pressure above the maximum-static-pressure.
• You can renumber SK numbers automatically.
• All calculations are in a text file, in the form of tables. You can open, you can copy, you can print directly at any time.
• You can use our software commands with AutoCAD or ZWCAD commands too.


### UPGRADE HISTORY

**JANUARY.2023**

AutoCAD 2021 x64, ZWCAD 2024 x64
Windows11 x64, Windows10 x64
.NET Framework 4.8
Sentinel HL Pro Driverless, Sentinel-LDK_SDK_9.0 x64

**JANUARY.2021**

AutoCAD 2021 x64, ZWCAD 2022 x64
Windows8.1 x64, Windows8.0 x64, Windows7 x64
.NET Framework 4
Sentinel HL Pro Driverless, Sentinel-LDK_SDK_7.6 x64

**JANUARY.2018**

AutoCAD 2018 x64, ZWCAD 2018 x64
Windows7 x64, Windows8.0 x64, Windows8.1 x64, Windows10 x64
Sentinel HASP HL Pro Driverless, Sentinel-LDK_SDK_7.6 x64

**MAY.2017**

AutoCAD 2017 x64, ZWCAD+ 2015 x64
Windows7 x64, Windows8.0 x64, Windows8.1 x64, Windows10 x64
Sentinel HASP HL MaxMicro Driverless, Sentinel-LDK_SDK_7.1 x64

**JANUARY.2015**

AutoCAD 2015 x64, ZWCAD+ 2015 x64
Windows7 x64, Windows8.0 x64, Windows8.1 x64
Sentinel HASP HL MaxMicro Driverless, Sentinel-LDK_SDK_7.1 x64

**JANUARY.2013**

AutoCAD 2013 x64
Windows7 x64
Sentinel HASP HL Max, Sentinel-HASP_SDK_5.12 x64

**JUNE.2012**

Windows7 x64, Windows8.0 x64, Windows8.1 x64
Sentinel HASP HL Max, Sentinel-HASP_SDK_5.12 x64

**JANUARY.2012**

Windows7 x32
Sentinel HASP HL Max, Sentinel-HASP_SDK_5.12 x64

**JANUARY.2010**

WindowsXP x32
Aladdin HASP HL Max, Ver1.1 x32

**JANUARY.2009**

WindowsXP x32
Aladdin HASP HL Max, Ver1.1 x32

**JANUARY.2003**

WindowsXP x32

**JANUARY.1999**

Windows98

**JANUARY.1997**

ACAD 14
Windows98

**JANUARY.1988**

MSDOS

WATER TRANSMISSION LINE DESIGN SOFTWARE
For Drawing / Modelling / Planning / Design / Analyze

OGUZLAR BILGISAYAR LTD.STI.

Über den Verkäufer OGUZLAR BILGISAYAR LTD.STI.

Kontakt aufnehmen

Plugins